Saturday, November 14, 2026

ACER ASPIRE 5310 5710 - COMPAL LA-3771P JDW50 JDY70 - REV 0.1 Schematic Download + Chip-Level Diagnostic Guide

The Acer Aspire 5310 and 5710 series, built on the Compal LA-3771P (JDW50/JDY70) motherboard, represents a classic era of Intel-based mobile computing. Utilizing the Intel 945/965 Express chipset architecture paired with the ICH8-M Southbridge, this board is a staple for technicians learning the fundamentals of the Intel power-on sequence. These legacy units often suffer from aging electrolytic capacitors and thermal stress on the Northbridge/Southbridge BGA joints. Understanding the specific Compal power rail transitions from ALW (Always On) to VS (Switched) is critical for successful chip-level repair.

Board Architecture & Technical Specifications

Motherboard Model / ODM Part Number Compal LA-3771P JDW50 JDY70 REV 0.1
Target Laptop Series / Form Factor Acer Aspire 5310 / 5710 (15.4" Multimedia Laptop)
Chipset / CPU Architecture Intel Core 2 Duo / Celeron M (Socket P) + Intel 965GM/PM + ICH8-M
Super I/O (EC/KBC) Controller ENE KB926QF (LPC Interface)
Key Voltage Rails & Switching Coils +3VALW (PL4), +5VALW (PL5), +1.05V_VCCP (PL8), +VCC_CORE (PL10, PL11)

Real-World Motherboard Diagnostic Procedures

1. Input Power Stage & DC-IN Protection Circuit

On the LA-3771P, the main power rail +19VB is distributed after the protection MOSFETs. Start by inspecting PQ1 and PQ2 (typically SI4407 or similar P-Channel MOSFETs). These are controlled by the Charging IC PU1 (ISL6251). If the laptop doesn't power on, check for 19V at PR1 (the main current sense resistor). If voltage is missing, verify ACIN (Pin 2) and DCIN (Pin 1) on PU1. A common failure point is a leaky decoupling capacitor on the gate line of the input MOSFETs, preventing the ISL6251 from driving the gates low to allow power through.

2. Standby & Secondary Rails Generation

The standby voltages +3VALW and +5VALW are generated by PU4 (MAX8734A). This IC must produce the LDO voltage +5V_ALW2 first to power the internal logic of the EC. Measure the resistance to ground on PL4 and PL5. A low resistance (under 100 ohms) on PL4 usually indicates a shorted ENE KB926QF Super I/O or a shorted Southbridge. If resistance is normal but the coils show 0V, check for the enable signal ONTIME and verify that the EC is releasing EC_ON to enable the buck converter stages.

3. Power-On Sequence & Signal State Tracking

When the power button is pressed, the ENE KB926QF (U20) receives the KBC_PWRBTN# signal. It then should release PM_SLP_S4# and PM_SLP_S3# to the Southbridge. In this era of boards, the 32.768kHz crystal (Y1) near the ICH8-M is a frequent culprit for "No Power" issues; if the crystal is not oscillating, the RTC section of the Southbridge will not wake up. Furthermore, if you have 3V/5V but no VCC_CORE, check PU10 (ISL6262). Ensure the VR_ON signal is arriving from the EC. If all rails are present but there is no display, the NEC/TOKIN capacitor (if present under the CPU socket) or the aging Northbridge BGA often requires inspection for thermal degradation.

Download Schematic File

⏳ Please wait 120 seconds to unlock your Schematic File download...
🔎 Read the chip-level diagnostic notes above while you wait.

Professional Repair Assistance

Explore our technician resources:

No comments:

Post a Comment

Translate

AdBlock Detected!

Please support Genius Mind Technologies by disabling your AdBlocker. We rely on ads to keep our massive library of free schematics, boardviews, and BIOS bin files free for everyone.