The Acer Aspire 3680, built on the venerable Compal LA-3151P (Columbia) motherboard architecture, represents a classic era of Intel 940/945 chipset engineering. As a senior engineer at geniusmind4u.blogspot.com, I frequently encounter these units in for repair. While these legacy machines are robust, they suffer from age-related thermal stress on the Northbridge (940GML/943GML) and specific capacitor degradation in the VRM circuit. This guide provides the technical roadmap for diagnosing no-power, no-display, and charging issues using the Compal nomenclature system.
Board Architecture & Technical Specifications
| Feature | Specification / Component |
|---|---|
| Motherboard Model / ODM Part Number | Compal LA-3151P / LA-3121P (Columbia) |
| Target Laptop Series | Acer Aspire 3680 / 5570 / 5580 |
| Chipset / CPU Architecture | Intel 940GML / 945GM + ICH7-M (Socket M) |
| Super I/O (EC/KBC) Controller | ENE KB910 / KB910LQF |
| Key Voltage Rails & Switching Coils | +3VALW (PL4), +5VALW (PL5), +1.8V_DDR (PL6), +VCC_CORE (PL10/PL11) |
Real-World Motherboard Diagnostic Procedures
1) Input Power Stage & DC-IN Protection Circuit
In the LA-3151P, the VIN rail (+19VB) is managed by the ISL6251 (PU1) charging IC. If the laptop is dead with no LEDs, first check the voltage at the drain of PQ1 and PQ2 (SI4407/AO4407).
- Gate Control: Ensure
PACINis high (approx. 3.3V) at the base of PQ5, which pulls down the gate of the P-Channel MOSFETs PQ1/PQ2 to allow 19V to pass to theB+rail. - Current Sensing: Check PR13 (0.01 ohm) for physical burns. If the ISL6251 does not detect
ACINon pin 23, it will not enable the charging circuit or the system power path.
2) Standby Power Generation (+3VALW / +5VALW)
The standby voltages are generated by PU4 (typically a MAX8734A or similar PWM). This is a common failure point in legacy Acer models.
- Coil Resistance: Measure resistance to ground on PL4 (+3VALW) and PL5 (+5VALW). A low resistance (<50 ohms) usually indicates a shorted ENE KB910 EC or a failed Southbridge ICH7-M.
- Enable Signals: Verify
ON5andON3signals from the EC. Without these, the buck converter will remain dormant. If+3VLP(LDO) is missing at pin 25 of PU4, the EC will never wake up to trigger the power-on sequence.
3) Power-On Sequence & Signal State Tracking
On this legacy Intel platform, the transition from S5 (Standby) to S0 (Working) relies heavily on the handshake between the ENE KB910 and the ICH7-M Southbridge.
- RTC Reset: Check the 3V CMOS battery and the 32.768kHz crystal (Y2) near the Southbridge. If the RTC clock is not oscillating, the ICH7-M will not release
RSMRST#. - Sleep Signals: When the power button is pressed, the EC sends
PWRBTN#to the Southbridge. MonitorPM_SLP_S3#andPM_SLP_S5#. If these signals stay low, the secondary rails (+1.8VS, +1.05VS, +VCC_CORE) will never initialize. - Legacy Tip: The Northbridge (Intel 945) on this board is prone to "dry joints" due to thermal cycling. If you have all voltages but no display (and VCORE is present), a gentle reflow of the Northbridge can often confirm a BGA failure.
Download Schematic & Boardview Files
🔎 Read the chip-level diagnostic notes above while you wait.
Professional Repair Assistance
Explore our technician resources:
- 🛠️ Diagnose No-Power & Short-Circuit faults step-by-step: Interactive Laptop Diagnostic Lab
- 🛒 Original Replacement Motherboards & IC Components: Official Spare Parts Mega Store
No comments:
Post a Comment