Sunday, November 15, 2026

ACER ASPIRE 7750 7750G LA-6911P Schematic Download + Chip-Level Diagnostic Guide

The Acer Aspire 7750 and 7750G, built on the robust Compal LA-6911P (P5WE0) motherboard, represent the pinnacle of the Intel Sandy Bridge era for 17-inch desktop replacements. This architecture utilizes the Intel HM65 chipset paired with Socket G2 processors and, in the 'G' variants, dedicated AMD Radeon HD graphics. For the bench technician, the LA-6911P is a classic Compal design, following strict rail sequencing and component labeling that makes it a prime candidate for successful chip-level recovery when armed with the right schematic and diagnostic logic.

Board Architecture & Technical Specifications

Feature Specification
Motherboard Model / ODM Part Number Compal LA-6911P (P5WE0)
Target Laptop Series / Form Factor Acer Aspire 7750 / 7750G (17.3" Desktop Replacement)
Chipset / CPU Architecture Intel HM65 PCH / 2nd Gen Intel Core (Sandy Bridge)
Super I/O (EC/KBC) Controller ENE KB930QF A1
Key Voltage Rails & Switching Coils +3VALW (PL27), +5VALW (PL28), +1.05VS (PL24), +VCC_CORE (PL20, PL21)

Real-World Motherboard Diagnostic Procedures

1) Input Power Stage & DC-IN Protection Circuit

The LA-6911P uses the ISL88731C (PU1) as the charging controller. Start by measuring the voltage at PR301 (the main current sense resistor). If you have 19V at the DC-in jack but 0V at PR301, inspect the two P-Channel input MOSFETs, PQ6 and PQ7. For these to conduct, the ISL88731C must output a low voltage (approx 8V-9V) on the ACDRV pin to pull the gates down. Check ACIN (Pin 13) which should be above 3.2V; if this signal is missing, the IC will not enable the power path. A common failure point is the breakdown of ceramic capacitors near the DC-in connector, causing a hard short to ground on the +19VB rail.

2) Standby & Secondary Rails Generation

The 3.3V and 5V Always-On rails are managed by PU11 (TPS51125). First, verify the LDO outputs: Pin 8 (VREG3) and Pin 17 (VREG5). These must be present for the ENE KB930QF Super I/O to initialize. If the LDOs are present but PL27 (+3VALW) and PL28 (+5VALW) are missing, check the ENTRIP1 and ENTRIP2 signals. On this board, a common issue is the PCH (HM65) shorting internally on the +3VALW rail. Use a multimeter to check the resistance to ground on PL27; a reading below 50 ohms often indicates a dead PCH or a compromised EC controller.

3) Power-On Sequence & Signal State Tracking

If the laptop has standby voltages but fails to trigger, monitor the EC_ON signal from the KB930QF. Once the power button is pressed, the EC should release PCH_RSMRST# (3.3V) to the HM65. If the PCH receives this and all RTC conditions are met (check 32.768kHz crystal Y3), it should respond with PM_SLP_S4# and PM_SLP_S3#. If these signals remain at 0V, the PCH is likely missing a power rail or the BIOS/ME region is corrupted. For the 7750G, also verify the +VGA_CORE rail at PL13; a shorted high-side MOSFET here can prevent the entire board from starting or lead to an immediate shutdown after 1 second.

Download Schematic File

⏳ Please wait 120 seconds to unlock your Schematic File download...
🔎 Read the chip-level diagnostic notes above while you wait.

Professional Repair Assistance

Explore our technician resources:

No comments:

Post a Comment

Translate

AdBlock Detected!

Please support Genius Mind Technologies by disabling your AdBlocker. We rely on ads to keep our massive library of free schematics, boardviews, and BIOS bin files free for everyone.