The Acer Aspire 4741Z, built on the robust Compal JE40-CP (LA-5891P) platform, represents a classic era of Intel 1st Generation Core architecture (Arrandale/HM55). For chip-level technicians, this board is a masterclass in Compal design logic, featuring the characteristic discrete power rail sequencing and the ubiquitous ENE KB926QF-D3 Super I/O. In this guide, we dive into the specific power-on requirements and common failure points of the HM55 chipset and the ISL6251 charging circuit.
Board Architecture & Technical Specifications
| Feature | Specification |
|---|---|
| Motherboard Model / ODM Part Number | Compal JE40-CP / LA-5891P |
| Target Laptop Series / Form Factor | Acer Aspire 4741Z / 14" Notebook |
| Chipset / CPU Architecture | Intel HM55 Express / Arrandale (PGA988) |
| Super I/O (EC/KBC) Controller | ENE KB926QF-D3 |
| Key Voltage Rails & Switching Coils | +3VALW (PL27), +5VALW (PL28), +1.05V_VTT (PL24), +VCC_CORE (PL22) |
Real-World Motherboard Diagnostic Procedures
1) Input Power Stage & DC-IN Protection Circuit
On the LA-5891P, the 19V input (VIN) must pass through the protection MOSFETs PQ1 and PQ2 (AO4407) to become the +19VB (B+) rail. This is controlled by the charging IC PU1 (ISL6251). If the laptop doesn't power on, measure the gate voltage at Pin 4 of PQ1. In a healthy state, the ISL6251 should output a drive signal to the gates; if the gate voltage is equal to the source (19V), the MOSFETs remain closed. Check PR3 (current sense resistor) for any signs of burning and ensure PACIN is high (approx 3.3V) at the base of PQ7 to enable the power path.
2) Standby & Secondary Rails Generation
The +3VALW and +5VALW rails are managed by PU16 (TPS51125). This is a critical stage; without these, the EC (KB926QF) will not wake up. Check for 3.3V on PL27 and 5V on PL28. If 3.3V is missing, measure the resistance to ground on PL27. A low resistance (below 50 ohms) often points to a shorted HM55 PCH or a leaky ceramic capacitor near the EC. Ensure the LDO voltages VREG3 (Pin 8) and VREG5 (Pin 17) are present at PU16, as these provide the internal logic power for the standby controller.
3) Power-On Sequence & Signal State Tracking
The trigger sequence starts when ON/OFFBTN# is pulled low and sent to the EC (Pin 32). The EC must then release EC_RSMRST# (3.3V) to the HM55 PCH to signal that standby power is stable. If the PCH receives this and all RTC requirements are met (3V on RTC_AUX_S5), it should respond by pulling PM_SLP_S4# and PM_SLP_S3# high. If these signals remain at 0V, the issue is likely a corrupted BIOS/ME Region dump or a dead 32.768kHz crystal (Y2). For this generation, always check for the "NEC/TOKIN" capacitor equivalent (if present on specific revisions) under the CPU socket, as its failure causes instant shutdown under load.
Download Schematic & Boardview Files
🔎 Read the chip-level diagnostic notes above while you wait.
Professional Repair Assistance
Explore our technician resources:
- 🛠️ Diagnose No-Power & Short-Circuit faults step-by-step: Interactive Laptop Diagnostic Lab
- 🛒 Original Replacement Motherboards & IC Components: Official Spare Parts Mega Store
No comments:
Post a Comment