Saturday, November 21, 2026

Acer Aspire 4750 4750G (Compal LA-6901P) Schematic & Boardview Download + Chip-Level Diagnostic Guide

The Acer Aspire 4750 and 4750G are quintessential examples of the Intel 2nd Generation (Sandy Bridge) era, built upon the highly successful Compal LA-6901P (P5WE0) motherboard architecture. As a technician, encountering this board is common, and while it is generally robust, it suffers from aging-related issues such as high-side MOSFET breakdowns in the CPU VRM and PCH standby rail shorts. This guide provides the official schematic and boardview files alongside a professional diagnostic breakdown tailored for the Compal design language.

Board Architecture & Technical Specifications

Component Specification / Part Number
Motherboard Model / ODM Part Number Compal LA-6901P (P5WE0 / P5W0H)
Target Laptop Series / Form Factor Aspire 4750, 4750G, 4752 (14-inch)
Chipset / CPU Architecture Intel HM65 Express / Sandy Bridge (PGA988B)
Super I/O (EC/KBC) Controller ENE KB930QF A1
Key Voltage Rails & Switching Coils +3VALW (PL27), +5VALW (PL28), +1.5V (PL15), +VCC_CORE (PL18/PL21)

Real-World Motherboard Diagnostic Procedures

1) Input Power Stage & DC-IN Protection Circuit

The LA-6901P utilizes a standard Compal charging circuit managed by the ISL88731C (PU1). If the laptop fails to power on and shows no LEDs, start by measuring +19VB at the current sense resistor PR302. If voltage is missing here, check the gates of the dual N-channel MOSFETs PQ6 and PQ7. The ISL88731C must output approximately 25V at pin 21 (ACDRV) to drive these gates. If pin 2 (ACIN) is below 3.2V, the IC will not enable the input MOSFETs. A common failure point is a shorted ceramic capacitor on the BATT+ rail or a leaky PQ6 causing the input fuse to blow.

2) Standby & Secondary Rails Generation

This board generates its always-on voltages using the PU16 (TPS51125 or RT8205L) buck converter. Measure the resistance to ground on PL27 (+3VALW) and PL28 (+5VALW). A low resistance (< 10 ohms) on PL27 often points to a failed ENE KB930QF Super I/O or a shorted HM65 PCH. If the rails are missing but no short is present, verify the ENTRIP1 and ENTRIP2 signals. In Compal logic, these are pulled low to enable the rails. If the EC does not release these lines via the EC_ON signal, the standby voltages will never appear.

3) Power-On Sequence & Signal State Tracking

For "No Display" or "Power-On, No Boot" scenarios, monitor the PM_SLP_S3# and PM_SLP_S4# signals from the PCH. These must transition from 0V to 3.3V when the power button is pressed. If the EC receives ON/OFFBTN# but fails to trigger PCH_PWRBTN#, check the 32.768kHz crystal (Y2) near the PCH. Furthermore, the LA-6901P is notorious for BIOS/ME Region corruption. If all voltages (+VCC_CORE on PL18, +VGFX_CORE on PL22) are present but there is no POST, a clean ME-Region dump flashed to the 4MB SPI chip (U36) is the standard professional fix.

Download Schematic & Boardview Files

⏳ Please wait 120 seconds to unlock your Schematic & Boardview Files download...
🔎 Read the chip-level diagnostic notes above while you wait.

Professional Repair Assistance

Explore our technician resources:

No comments:

Post a Comment

Translate

AdBlock Detected!

Please support Genius Mind Technologies by disabling your AdBlocker. We rely on ads to keep our massive library of free schematics, boardviews, and BIOS bin files free for everyone.