Sunday, November 22, 2026

Acer Aspire 4736Z Compal LA-4494P Schematic Download + Chip-Level Diagnostic Guide

The Acer Aspire 4736Z, built on the robust Compal LA-4494P (KALA0) motherboard architecture, represents a classic era of Intel Core 2 Duo mobile computing. As a senior engineer, I've seen this board frequently on the bench, primarily due to its aging power delivery system and the infamous NEC/TOKIN capacitor degradation. This guide provides the technical roadmap for diagnosing the DDR3 variant of this platform, focusing on the specific rail sequencing and chip-level failures common to the Intel Cantiga chipset paired with the ICH9M Southbridge.

Board Architecture & Technical Specifications

Motherboard Model / ODM Part NumberCompal LA-4494P (KALA0) Rev 1.0
Target Laptop Series / Form FactorAcer Aspire 4736 / 4736Z / 4736G (14.0" LED)
Chipset / CPU ArchitectureIntel Penryn (Core 2 Duo) + GM45/PM45 + ICH9M
Super I/O (EC/KBC) ControllerENE KB926QF-D3
Key Voltage Rails & Switching Coils+3VALW (PL4), +5VALW (PL5), +1.5V_DDR3 (PL6), +VCC_CORE (PL10, PL11)

Real-World Motherboard Diagnostic Procedures

1) Input Power Stage & DC-IN Protection Circuit

The LA-4494P utilizes the ISL6251 (PU1) as its primary charging controller. Start by measuring the voltage at PR1 (Current Sense Resistor). If you only see 0V-2V, inspect the two P-Channel entry MOSFETs, PQ1 and PQ2. A common failure occurs when the EC (KB926QF) does not receive a valid ACIN signal on pin 23 of PU1. For the gates of PQ1/PQ2 to open, the signal PACIN must be high, which then allows ACON to pull the gates low via the resistor divider. If the laptop runs on battery but not on AC, check PQ4 for leakage.

2) Standby Rail Generation & 3V/5V ALW Faults

The +3VALW and +5VALW rails are generated by PU4 (ISL6236 or RT8206A). Before replacing the IC, measure the resistance to ground on PL4 and PL5. A low resistance (<50 ohms) on PL4 often indicates a punctured Southbridge (ICH9M) or a shorted KB926QF. Also, verify the LDO output on pin 7 (LDO5) of PU4; this 5V reference is critical for the initial wake-up of the EC. If LDO is present but the coils are dead, verify EN_LDO and the feedback resistors PR44/PR46.

3) Power-On Sequence & The VCC_CORE Filter Issue

If the board triggers but displays no video or suffers from random reboots under load, the primary suspect on the LA-4494P is the NEC/TOKIN OE128 (or OE907) capacitor located directly under the CPU socket. This high-capacitance proadlizer degrades over time, causing excessive ripple on +VCC_CORE. The professional solution is to remove it and replace it with four 330uF Tantalum capacitors. Additionally, ensure PM_SLP_S3# and SYSON signals are reaching the secondary rail controllers (PU5, PU6) to enable the DDR3 and PCH voltages.

Download Schematic File

⏳ Please wait 120 seconds to unlock your Schematic File download...
🔎 Read the chip-level diagnostic notes above while you wait.

Professional Repair Assistance

Explore our technician resources:

No comments:

Post a Comment

Translate

AdBlock Detected!

Please support Genius Mind Technologies by disabling your AdBlocker. We rely on ads to keep our massive library of free schematics, boardviews, and BIOS bin files free for everyone.