The Acer Aspire 5517 and 5532 series are built on the Compal LA-5481P (NAWA2) motherboard architecture. This platform utilizes the AMD Puma mobile ecosystem, featuring the RS780MN Northbridge and SB710 Southbridge paired with AMD Athlon or Turion 64 X2 processors. As a senior engineer, I often see these boards in the shop with classic aging symptoms, ranging from thermal-induced Northbridge failure to power rail collapses in the standby circuit. This guide focuses on the chip-level logic required to revive these legacy workhorses using the schematics.
Board Architecture & Technical Specifications
| Motherboard Model / ODM Part Number | Compal LA-5481P (NAWA2) Rev 1.0 |
| Target Laptop Series / Form Factor | Acer Aspire 5517 / 5532 (15.6" Legacy) |
| Chipset / CPU Architecture | AMD RS780MN + SB710 (Socket S1g3) |
| Super I/O (EC/KBC) Controller | ENE KB926QF-D3 |
| Key Voltage Rails & Switching Coils | +3VALW (PL4), +5VALW (PL5), +1.1V_NB (PL8), +VCC_CORE (PL10/11) |
Real-World Motherboard Diagnostic Procedures
1) DC-IN Protection & Charging Logic Analysis
In the LA-5481P, the input power enters through the DC jack and passes through the first protection MOSFET PQ1 and second FET PQ2. The system main rail, +19VB (B+), is managed by the ISL6251AHRZ (PU1) charging IC. If the laptop fails to power on and shows 0A on the DC power supply, check the voltage at PR6. If you have 19V at the drain of PQ1 but 0V at the source of PQ2, inspect PACIN (pin 23 of PU1). If PACIN is low, the charging IC is not detecting the adapter, often due to a faulty voltage divider at the ACSET pin or a leaky decoupling capacitor on the gate control line.
2) Standby Power Generation (+3VALW / +5VALW)
The LA-5481P uses the ISL6237 or RT8206B (PU4) to generate the Always-On rails. Before the power button is pressed, you must confirm +3VALW on PL4 and +5VALW on PL5. If these rails are missing, check the LDO output (pin 7, LDO3). If the LDO is present but the switching rails are absent, verify that the EC (KB926QF) is sending the EN_MAIN signal. A common failure point on this board is a shorted ceramic capacitor near the Northbridge which pulls the +1.1V_NB rail (PL8) to ground, preventing the secondary power-up sequence even if standby rails are healthy.
3) Power-On Sequence & AMD Northbridge Failure
The sequence follows standard Compal logic: EC_ON → 3.3V/5V_ON → MAINON → SUSP#. If the laptop turns on but has no display (black screen), check the +VCC_CORE on PL10 and PL11. If CPU core voltage is present, the most frequent culprit on the LA-5481P is the AMD RS780MN Northbridge. Due to thermal stress, the solder balls or the internal die connection often fail. Before attempting a reball or replacement, perform a "reflow test" at 200°C for 30 seconds; if the display returns, the chip requires replacement. Additionally, always verify the 32.768kHz crystal (Y2) near the Southbridge if the board fails to trigger RSMRST#.
Download Schematic File
🔎 Read the chip-level diagnostic notes above while you wait.
Professional Repair Assistance
Explore our technician resources:
- 🛠️ Diagnose No-Power & Short-Circuit faults step-by-step: Interactive Laptop Diagnostic Lab
- 🛒 Original Replacement Motherboards & IC Components: Official Spare Parts Mega Store
No comments:
Post a Comment