Sunday, November 15, 2026

ACER ASPIRE 5552 - COMPAL LA-6552P PEW76-86-96 - REV 1.0 Schematic Download + Chip-Level Diagnostic Guide

The ACER ASPIRE 5552, built on the Compal LA-6552P (PEW76) motherboard, is a classic example of the AMD Champlain platform era. This board utilizes the AMD RS880M Northbridge and SB850/SB820 Southbridge architecture. For chip-level technicians, this board is notorious for Northbridge BGA failures and specific PWM controller issues in the standby circuit. This guide provides the technical roadmap for diagnosing common power-rail failures and signal sequencing issues using the Compal naming convention.

Board Architecture & Technical Specifications

FeatureTechnical Detail
Motherboard Model / ODM Part NumberCompal LA-6552P PEW76-86-96 REV 1.0
Target Laptop Series / Form FactorAcer Aspire 5552 / 5552G Series (15.6")
Chipset / CPU ArchitectureAMD S1G4 (Athlon II/Phenom II) + RS880M Northbridge
Super I/O (EC/KBC) ControllerENE KB926QF-D3
Key Voltage Rails & Switching Coils+3VALW (PL27), +5VALW (PL28), +1.1V_NB (PL24), +VCC_CORE (PL20, PL21)

Real-World Motherboard Diagnostic Procedures

1) Input Power Stage & DC-IN Protection Circuit

The LA-6552P uses a pair of P-Channel MOSFETs (typically PQ1 and PQ2) to pass the +19VB rail to the main system B+ line. If the laptop is dead with 0A current draw, first measure the voltage at PR3 (the main current sense resistor). If B+ is missing, check the ISL6251 (PU1) charging IC. Specifically, verify ACSET (Pin 2) and DCIN (Pin 24). If the gate voltage on PQ1/PQ2 is approximately 19V, the MOSFETs are not being pulled low to conduct; this usually indicates a short circuit on the B+ rail or a faulty charging IC failing to output the PACIN signal.

2) Standby & Secondary Rails Generation

The Always-On rails (+3VALW and +5VALW) are generated by PU11 (TPS51125). Before checking the switching output at PL27 and PL28, ensure the LDO voltages are present: VREG3 (Pin 8) and VREG5 (Pin 17). A common failure point on this board is a low resistance on the +3VALW rail caused by a partially shorted ENE KB926QF EC chip. Normal resistance to ground on PL27 should be in the kilo-ohm range. If you find less than 50 ohms, inject 1V into the rail and check if the EC or the Southbridge heats up.

3) Power-On Sequence & Signal State Tracking

On the AMD platform, the power-up sequence depends heavily on the Northbridge (RS880M) health. Once the power button is pressed, the EC sends ON/OFFBTN# to the Southbridge. Monitor PM_SLP_S3# and PM_SLP_S5#; if these signals do not transition to 3.3V, the Southbridge is not initiating the wake state. For "No Display" symptoms—a very common issue on the Aspire 5552—check the +1.1V_NB rail at PL24. If the voltage is present but there is no POST, the AMD 216-0752001 Northbridge often requires reballing or replacement due to internal solder bump degradation.

Download Schematic File

⏳ Please wait 120 seconds to unlock your Schematic File download...
🔎 Read the chip-level diagnostic notes above while you wait.

Professional Repair Assistance

Explore our technician resources:

No comments:

Post a Comment

Translate

AdBlock Detected!

Please support Genius Mind Technologies by disabling your AdBlocker. We rely on ads to keep our massive library of free schematics, boardviews, and BIOS bin files free for everyone.