The Acer Aspire R3-131T, built on the CNOTE-1 R30 (Wistron Woody_BS) motherboard, is a popular 11.6-inch convertible laptop utilizing the Intel Braswell SoC platform. For chip-level technicians, this board presents unique challenges due to its high integration, where the CPU, PCH, and GPU are combined into a single System-on-Chip (SoC). Common failures often involve the power management circuit and the 3.3V/5V standby generation, which is critical for the device to wake from its low-power S5 state.
Board Architecture & Technical Specifications
| Feature | Technical Specification |
|---|---|
| Motherboard Model / ODM Part Number | CNOTE-1 R30 / Wistron Woody_BS 14235-1 |
| Target Laptop Series / Form Factor | Acer Aspire R3-131T / Cloudbook 11 |
| Chipset / CPU Architecture | Intel Braswell (Celeron N3050 / Pentium N3700) |
| Super I/O (EC/KBC) Controller | ITE IT8987E-BX |
| Key Voltage Rails & Switching Coils | DCBATOUT (19V), 3D3V_AUX_S5 (PL4501), 5V_AUX_S5 (PL4502), 1D0V_S0 (PL4801) |
Real-World Motherboard Diagnostic Procedures
1) Input Power Stage & DC-IN Protection Circuit
On the Wistron Woody platform, the primary 19V rail is identified as DCBATOUT. The charging circuit is managed by the PU4001 (BQ24735) IC. If the board is completely dead, first measure the voltage at the drain of the second protection MOSFET PQ4002. For the gates to open, the BQ24735 must output ~25V on the ACDRV (pin 4) signal. This requires ACDET (pin 6) to be approximately 2.6V, derived from a resistor divider on the adapter input. If ACDET is present but ACDRV is missing, check for a short on DCBATOUT by measuring resistance to ground at the current sense resistor PR4002; a reading below 10 ohms usually indicates a shorted high-side MOSFET in one of the buck converter stages.
2) Standby & Secondary Rails Generation
This board utilizes the TPS51225 (PU4501) to generate the 3D3V_AUX_S5 and 5V_AUX_S5 standby rails. Before these switching rails appear, the IC must output its internal LDO voltages: VREG3 (3.3V) and VREG5 (5V). These LDOs power the ITE IT8987E EC controller. If the LDOs are present but the coils PL4501 and PL4502 are inactive, verify the enable signals 3D3V_EN_R and 5V_EN_R coming from the EC. In many R3-131T units, a liquid spill near the touchpad connector often corrodes the traces for these enable signals, preventing the laptop from entering an S5 standby state.
3) Power-On Sequence & Signal State Tracking
The Wistron power sequence for Braswell is strictly timed. When the power button is pressed, the EC pulls KBC_PWRBTN# low, which then triggers SIO_PWRBTN# to the SoC. The SoC must then release PM_SLP_S4# and PM_SLP_S3# to high logic levels. If the laptop triggers but immediately shuts down, check the ALL_SYS_PWRGD signal at PQ4405. If any secondary rail (like 1.0V SoC core or 1.35V DDR3L) fails to stabilize, this signal remains low, forcing a system reset. Additionally, ensure the 32.768kHz RTC crystal is oscillating; without the RTC clock, the Intel SoC will never initiate the wake-up sequence from deep sleep.
Download Schematic & Boardview Files
🔎 Read the chip-level diagnostic notes above while you wait.
Professional Repair Assistance
Explore our technician resources:
- 🛠️ Diagnose No-Power & Short-Circuit faults step-by-step: Interactive Laptop Diagnostic Lab
- 🛒 Original Replacement Motherboards & IC Components: Official Spare Parts Mega Store
No comments:
Post a Comment