Thursday, November 19, 2026

Acer Aspire V5-572G (Compal LA-9531P / ACER-5521P) Schematic & Boardview + Chip-Level Repair Guide

The Acer Aspire V5-572 and V5-472 series, built on the Compal LA-9531P (ACER-5521P) motherboard architecture, represent a pivotal era of thin-and-light laptop design. These boards utilize a highly integrated Intel Ivy Bridge or Haswell U-series platform, often paired with dedicated NVIDIA GT 700M series graphics. For the chip-level engineer, this board presents unique challenges, particularly regarding the ENE KB9012 internal firmware and the sensitive power distribution logic required for its slim chassis.

Board Architecture & Technical Specifications

FeatureSpecification / Component
Motherboard Model / ODM Part NumberCompal LA-9531P (Revision 1.0/2.0)
Target Laptop Series / Form FactorAcer Aspire V5-572G, V5-572P, V5-472G
Chipset / CPU ArchitectureIntel Ivy Bridge ULV / HM77 PCH
Super I/O (EC/KBC) ControllerENE KB9012QF-A3 (Programmable)
Key Voltage Rails & Switching CoilsPL402 (+3VALW), PL403 (+5VALW), PL701 (+VCC_CORE), PL302 (+VCHGR)

Real-World Motherboard Diagnostic Procedures

1) Input Power Stage & DC-IN Protection Circuit

The LA-9531P utilizes a BQ24725A (PU301) charging IC to manage the entry of the +19VB rail. If the laptop is dead with no lights, first check the voltage at the current sense resistor PR301. If you see 0V, inspect the gates of the dual N-Channel MOSFETs PQ301 and PQ302. The ACDRV signal (Pin 4 of PU301) must reach approximately ~25V to drive these gates. If ACDRV is low, verify that ACDET (Pin 6) is at ~2.6V via the resistor divider from the DC jack. A common failure on this board is a shorted ceramic capacitor on the +19VB line, which causes the BQ IC to enter protection mode and shut down the input MOSFETs.

2) Standby & Secondary Rails Generation

This board generates its 3.3V and 5V Always-On rails using the SY8208B (PU401) and SY8208C (PU402) buck converters. Unlike older platforms that use a single PWM for both, these independent chips are prone to localized failure. Measure the resistance to ground on PL402 (+3VALW) and PL403 (+5VALW). A low resistance (below 100 ohms) on PL402 often points to a punctured ENE KB9012 Super I/O or a shorted PCH core. If the rails are present but the laptop won't trigger, ensure EC_ON is being sent from the KBC to enable the secondary VS rails once the power button is pressed.

3) Power-On Sequence & Signal State Tracking

The power-on logic for the ACER-5521P is heavily dependent on the KB9012. When the power button is pressed, the signal ON/OFFBTN# should drop to 0V at Pin 110 of the EC. The EC then releases PCH_PWRBTN# to the Intel PCH. If the PCH receives this and its RTC section is healthy (check 32.768kHz crystal Y2), it should respond by pulling PM_SLP_S3# and PM_SLP_S4# high. If these signals remain low, the most common culprit in this specific Acer model is a corrupted BIOS or, more frequently, corrupted internal firmware within the KB9012 itself. A clean ME-region BIOS flash and an EC firmware re-program are standard requirements for "No Power" or "Power On, No Display" symptoms on this platform.

Download Schematic & Boardview Files

⏳ Please wait 120 seconds to unlock your Schematic & Boardview Files download...
🔎 Read the chip-level diagnostic notes above while you wait.

Professional Repair Assistance

Explore our technician resources:

No comments:

Post a Comment

Translate

AdBlock Detected!

Please support Genius Mind Technologies by disabling your AdBlocker. We rely on ads to keep our massive library of free schematics, boardviews, and BIOS bin files free for everyone.