Thursday, November 19, 2026

AS 5560 5560G - WISTRON JE50-SB - REV SB - 2011 Schematic Download + Chip-Level Diagnostic Guide

The Acer Aspire 5560 and 5560G, built on the Wistron JE50-SB motherboard, represents a classic era of AMD's Sabine platform. Utilizing the FS1 socket for A-series Llano APUs, this board is a staple for technicians dealing with legacy AMD hardware. This guide provides a deep-dive into the chip-level architecture, focusing on common failure points like the FCH (Fusion Controller Hub) and the specific power-rail sequencing used by Wistron during the 2011 production cycle.

Board Architecture & Technical Specifications

Component Details
Motherboard Model / ODM Part Number Wistron JE50-SB (48.4M702.0SB)
Target Laptop Series / Form Factor Acer Aspire 5560 / 5560G (15.6")
Chipset / CPU Architecture AMD Sabine / Hudson-M2 FCH (A50M/A60M)
Super I/O (EC/KBC) Controller Nuvoton NPCE795LA0DX
Key Voltage Rails & Switching Coils DCBATOUT, 3D3V_AUX_S5 (PL4101), 5V_AUX_S5 (PL4102), 1D1V_S0

Real-World Motherboard Diagnostic Procedures

1) Input Power Stage & DCBATOUT Protection Circuit

On the Wistron JE50-SB, the main system rail is labeled DCBATOUT. The entry circuit typically utilizes a BQ24707 charging IC. Start by measuring the voltage at the current sense resistor R0201. If you have 19V at the DC jack but 0V at R0201, inspect the two N-channel MOSFETs (often AO4407 or similar). Check the AC_IN signal (Pin 6 of BQ24707); it must be around 2.4V to 3V for the IC to drive the gates of the input protection MOSFETs. If the gates are not being pulled high, check for a short to ground on the DCBATOUT line—a common culprit is a shorted ceramic decoupling capacitor near the CPU or GPU buck converters.

2) Standby & Secondary Rails Generation

The JE50-SB relies on the TPS51123 (or equivalent) to generate the 3D3V_AUX_S5 and 5V_AUX_S5 always-on rails. First, verify the LDO outputs: Pin 8 (VREG3) and Pin 17 (VREG5). These must be present for the NPCE795 EC to initialize. If the LDOs are present but the main coils PL4101 and PL4102 show no voltage, check the 3D3V_5V_EN signal from the EC. Note that on this AMD platform, the 3.3V rail often has a resistance-to-ground norm of roughly 300-500 ohms, while the 5V rail should be in the kilo-ohm range. If 3D3V_AUX_S5 is missing, the FCH will never release the power-on sequence.

3) Power-On Sequence & Signal State Tracking

Tracing the trigger on Wistron boards requires monitoring the KBC_PWRBTN# signal. When the power button is pressed, this signal should drop from 3.3V to 0V and return. The EC then sends SIO_PWRBTN# to the AMD FCH. Crucially, check RSMRST# (Resume Reset); it must be 3.3V for the FCH to exit its sleep state. If the laptop turns on but has no display, the AMD Sabine platform is notorious for FCH internal failures or cold solder joints. Before reflowing, verify ALL_SYS_PWRGD at the EC. If this signal is missing, one of the secondary rails (like 1D1V_VTT or 1D2V_S3) is failing to stabilize, preventing the BIOS from executing the POST routine.

Download Schematic File

⏳ Please wait 120 seconds to unlock your Schematic File download...
🔎 Read the chip-level diagnostic notes above while you wait.

Professional Repair Assistance

Explore our technician resources:

No comments:

Post a Comment

Translate

AdBlock Detected!

Please support Genius Mind Technologies by disabling your AdBlocker. We rely on ads to keep our massive library of free schematics, boardviews, and BIOS bin files free for everyone.