Thursday, November 19, 2026

Acer TravelMate 4330 4630 4630Z 4730 4730G (JALA0 LA-4221P) Schematic Download + Chip-Level Repair Guide

The Acer TravelMate 4330/4630/4730 series, built on the robust Compal JALA0 LA-4221P motherboard, represents the pinnacle of the Intel Centiga (GM45/PM45) era. As a senior engineer, I often see these units on the bench for power-cycling issues or total power failure. This board utilizes the Intel Core 2 Duo (Penryn) architecture paired with the ICH9M Southbridge, a platform known for its longevity but also for specific thermal-related component degradation.

Board Architecture & Technical Specifications

Component Specification / Identifier
Motherboard Model / ODM Part Number Compal JALA0 LA-4221P
Target Laptop Series TravelMate 4330, 4630, 4630Z, 4730, 4730G
Chipset / CPU Architecture Intel GM45/PM45 + ICH9M (Socket P)
Super I/O (EC/KBC) Controller ENE KB926QF-D3
Key Voltage Rails & Switching Coils PL4 (+3VALW), PL5 (+5VALW), PL10 (+VCC_CORE), PL6 (+1.8V_DDR2)

Real-World Motherboard Diagnostic Procedures

1) Input Power Stage & DC-IN Protection Circuit

On the LA-4221P, the VIN rail starts at the DC jack and passes through PQ1 and PQ2 (typically SI4407 P-Channel MOSFETs). If you have 19V at the adapter but 0V on the B+ (+19VB) rail at current sense resistor PR3, inspect the Charging IC PU1 (ISL6251).

  • Check PU1 Pin 24 (DCIN) for 19V and Pin 1 (VREF) for 2.39V.
  • If ACPRN# (Pin 23) is high, the MOSFETs won't gate. This is often caused by a leaky ceramic capacitor on the gate line or a faulty ISL6251.

2) Standby Rails & The Infamous NEC/TOKIN Issue

The +3VALW and +5VALW rails are generated by PU4 (TPS51125). If these are missing, check PL4 and PL5 for shorts to ground. However, the most common "No Power" or "Shutdown under load" symptom on this specific era of Acer boards is the degradation of the NEC/TOKIN OE128 proadlizer capacitor located directly under the CPU socket.

  • If the laptop works on battery but crashes on AC, or if +VCC_CORE at PL10 shows high ripple on an oscilloscope, replace the NEC/TOKIN with four 330uF Tantalum capacitors (ESR < 9mΩ) to stabilize the CPU voltage.

3) Power-On Sequence & Signal State Tracking

To trigger the transition from S5 (Standby) to S0 (On), the ENE KB926 must receive ACIN (approx 3V) from the charging circuit.

  • When the power button is pressed, ON/OFFBTN# (Pin 32) should drop to 0V and return to 3.3V.
  • The EC then sends PCH_RSMRST# to the ICH9M Southbridge. If the Southbridge is healthy, it responds with PM_SLP_S3# and PM_SLP_S5#.
  • If the board spins the fan for 2 seconds and stops, verify the +1.05VS_VCCP rail and ensure the BIOS/ME region isn't corrupted; a clean dump on a new SPI Flash chip is often required for this legacy platform.

Download Schematic File

⏳ Please wait 120 seconds to unlock your Schematic File download...
🔎 Read the chip-level diagnostic notes above while you wait.

Professional Repair Assistance

Explore our technician resources:

No comments:

Post a Comment

Translate

AdBlock Detected!

Please support Genius Mind Technologies by disabling your AdBlocker. We rely on ads to keep our massive library of free schematics, boardviews, and BIOS bin files free for everyone.