Friday, November 20, 2026

Acer Aspire 5560 Wistron GRADA-D AG1 Schematic Download + Chip-Level Diagnostic Guide

The Acer Aspire 5560, built on the Wistron GRADA-D (AG1) platform, is a classic representative of the AMD Sabine architecture era. Utilizing the AMD Llano APU and Hudson-M2 FCH, this motherboard is known for specific power sequence complexities and thermal-related failures in the FCH chipset. As a senior engineer at geniusmind4u.blogspot.com, I have compiled this guide to help you navigate the DCBATOUT distribution and the complex S5-to-S0 state transitions unique to Wistron’s engineering logic.

Board Architecture & Technical Specifications

Component / Feature Specification Details
Motherboard Model / ODM Part Number Wistron GRADA-D AG1 (10302-1)
Target Laptop Series Acer Aspire 5560 / 5560G
Chipset / CPU Architecture AMD Sabine (FS1 Socket) + Hudson-M2 FCH
Super I/O (EC/KBC) Controller ENE KB930QF-A1
Key Voltage Rails & Switching Coils DCBATOUT (19V), 3D3V_AUX_S5 (PL4101), 5V_AUX_S5 (PL4102), 1D1V_S0 (PL4301)

Real-World Motherboard Diagnostic Procedures

1. Input Power Stage & DC-IN Protection Circuit

In the Wistron GRADA-D, the primary 19V rail is labeled DCBATOUT. If the laptop is completely dead, start by checking the input MOSFETs (usually PU4001 and PU4002). These are P-Channel MOSFETs on many Wistron boards of this era, controlled by the Charging IC (typically ISL88731C). Verify that ACAV_IN is high (3.3V) at the SIO. If the gates of the isolation MOSFETs are not being pulled low, check the current sensing resistor R6000 for burns or an open circuit. A common failure point here is a shorted ceramic capacitor on the DCBATOUT line, which will cause the adapter light to blink or go out immediately upon connection.

2. Standby & Secondary Rails Generation

The Wistron AG1 uses a dual buck converter (often the TPS51123) to generate 3D3V_AUX_S5 and 5V_AUX_S5. These rails must be present before the power button is pressed. Use your multimeter to check the resistance to ground on coils PL4101 (3.3V) and PL4102 (5V). A low resistance (under 50 ohms) on the 3.3V rail often indicates a punctured ENE KB930 SIO or a shorted FCH chipset. If voltages are missing but resistance is high, verify the ENTRIP1 and ENTRIP2 signals; if these are not pulled down to ground by the SIO logic, the buck converter will remain in standby mode.

3. Power-On Sequence & Signal State Tracking

For the Aspire 5560 to trigger, the SIO must receive KBC_PWRBTN# (3.3V falling to 0V when the button is pressed). The SIO then sends SIO_PWRBTN# to the AMD FCH. The FCH must then respond by releasing PM_SLP_S5# and PM_SLP_S3#. On this AMD platform, if the 32.768kHz crystal (Y2) is not oscillating, the FCH will never release the sleep signals. If the laptop spins the fan for 2 seconds and dies, check the 1D1V_S0 rail (PL4301) and the 1D05V_VTT rail. Often, a corrupted BIOS or a failing AMD APU (due to cracked solder balls under the FS1 socket) prevents the ALL_SYS_PWRGD signal from reaching the required 3.3V high state.

Download Schematic File

⏳ Please wait 120 seconds to unlock your Schematic File download...
🔎 Read the chip-level diagnostic notes above while you wait.

Professional Repair Assistance

Explore our technician resources:

No comments:

Post a Comment

Translate

AdBlock Detected!

Please support Genius Mind Technologies by disabling your AdBlocker. We rely on ads to keep our massive library of free schematics, boardviews, and BIOS bin files free for everyone.