Friday, November 20, 2026

ACER ASPIRE 5734Z 5735Z - COMPAL LA-4855P PAWF5 6 - REV 0.1SEC Schematic Download + Chip-Level Diagnostic Guide

Welcome back to geniusmind4u.blogspot.com. Today, we are diving into the circuit analysis of the Acer Aspire 5734Z and 5735Z, specifically the Compal LA-4855P (PAWF5 6) motherboard. This platform represents the pinnacle of the Intel Core 2 Duo era, utilizing the GL40/GM45 Northbridge and ICH9M Southbridge architecture. While these machines are considered legacy, they are still frequently encountered on the repair bench for power-on failures and stability issues often linked to aging filtering capacitors and thermal stress on the BGA chipsets.

Board Architecture & Technical Specifications

Feature Specification
Motherboard Model / ODM Part Number Compal LA-4855P PAWF5 6 - REV 0.1SEC
Target Laptop Series / Form Factor Acer Aspire 5734Z / 5735Z (15.6")
Chipset / CPU Architecture Intel Penryn (Socket P) + GL40/GM45 + ICH9M
Super I/O (EC/KBC) Controller ENE KB926QF D3
Key Voltage Rails & Switching Coils +3VALW (PL4), +5VALW (PL5), +1.05VS (PL11), +VCC_CORE (PL12, PL13)

Real-World Motherboard Diagnostic Procedures

1) Input Power Stage & DC-IN Protection Circuit

On the LA-4855P, the 19V rail (B+) is managed by the charging IC PU1 (ISL6251). If the laptop is completely dead with no lights, first measure the voltage at the current sense resistor PR3. If 19V is missing here, check the gates of the protection MOSFETs PQ1 and PQ2. These are P-Channel MOSFETs; their gates must be lower than the source voltage to conduct. The PACIN signal, generated from the voltage divider after the DC-IN jack, must be high (~3.3V) to allow the circuit to pull the gates low. If ACOK is missing from pin 23 of PU1, the battery will not charge and the system may not switch to AC power.

2) Standby Rails Generation & Common Faults

The Always-On rails (+3VALW and +5VALW) are generated by PU4 (TPS51125). Before replacing the IC, measure the resistance to ground on PL4 and PL5. A common failure point in this era is a shorted decoupling capacitor on the +5VALW rail or a failed ENE KB926QF EC chip pulling down the +3VALW_EC line. Normal resistance on PL4 should be above 300 ohms. If the LDO outputs (VREG3/VREG5) are present but the coils are not switching, verify that the EN0 signal (pin 13) is active. Note: In Acer laptops of this generation, if the CMOS battery is below 2.5V, the EC may fail to trigger the power-on sequence correctly.

3) VCC_CORE Stability & The NEC/TOKIN Issue

A specific "legacy" issue for the Aspire 5734Z/5735Z involves the NEC/TOKIN OE128 (or similar) Proadlizer capacitor located directly under the CPU socket on the bottom of the board. Over time, this capacitor loses its ESR properties, leading to ripples in +VCC_CORE. Symptoms include the laptop freezing when the AC adapter is plugged in or crashing under high CPU load. The professional fix is to remove the NEC/TOKIN and replace it with four 330uF Tantalum capacitors (2.5V or 6.3V) in parallel. Additionally, ensure IMVP_PWRGD is reaching the ICH9M to allow the system to exit the reset state.

Download Schematic File

⏳ Please wait 120 seconds to unlock your Schematic File download...
🔎 Read the chip-level diagnostic notes above while you wait.

Professional Repair Assistance

Explore our technician resources:

No comments:

Post a Comment

Translate

AdBlock Detected!

Please support Genius Mind Technologies by disabling your AdBlocker. We rely on ads to keep our massive library of free schematics, boardviews, and BIOS bin files free for everyone.