Friday, November 20, 2026

Acer Aspire 5730Z / 5330 Compal LA-4201P JAL90 Schematic & Boardview Download + Chip-Level Diagnostic Guide

The Acer Aspire 5730Z and 5330 series are built upon the robust Compal JAL90 (LA-4201P) motherboard architecture. This platform, featuring the Intel GL40/GM45 chipset paired with the ICH9M Southbridge, represents the peak of the Core 2 Duo era. For chip-level technicians, this board is a classic example of Compal’s logic design, utilizing discrete buck converters for every major rail and a dedicated ENE Super I/O. Understanding the power states from S5 to S0 on this board is essential for reviving these legacy machines, which often suffer from aging electrolytic capacitors and thermal stress on the Northbridge.

Board Architecture & Technical Specifications

FeatureSpecification
Motherboard Model / ODM Part NumberCompal LA-4201P (JAL90)
Target Laptop Series / Form FactorAcer Aspire 5730Z / 5330 (15.4" Multimedia)
Chipset / CPU ArchitectureIntel Penryn CPU + GL40/GM45 NB + ICH9M SB
Super I/O (EC/KBC) ControllerENE KB926QF D3
Key Voltage Rails & Switching Coils+3VALW (PL4), +5VALW (PL5), +1.05V_VCCP (PL10), +VCC_CORE (PL11/PL12)

Real-World Motherboard Diagnostic Procedures

1) Input Power Stage & DC-IN Protection Circuit

On the LA-4201P, the primary 19V rail (+B) is managed by the ISL6251 (PU1) charging IC. If the laptop is dead with no LEDs, first check the voltage at the drain of PQ1 and PQ2 (the DC-IN MOSFETs). The ISL6251 must output a high signal on GATEP (Pin 20) to drive these P-Channel MOSFETs. Ensure ACSET (Pin 2) is above 1.26V, which is derived from the DC-IN voltage divider. If PQ1/PQ2 are not opening, check the current sense resistor PR3 for a blown state or high resistance, which triggers the over-current protection (OCP) loop.

2) Standby & Secondary Rails Generation

The Always-On rails (+3VALW and +5VALW) are generated by PU4 (TPS51125). Before pressing the power button, you must verify VREG3 and VREG5 (LDO outputs) on pins 8 and 17. If these are missing, the IC is likely defective or the EN0 pin is low. Measure the resistance to ground on PL4 and PL5. A common fault on this aging board is a short-circuited decoupling capacitor on the +5VALW rail, often located near the USB ports or the PCMCIA slot. Resistance on PL4 should typically be above 300 ohms; if it's below 50 ohms, the ICH9M or the ENE EC might be partially shorted.

3) Power-On Sequence & Signal State Tracking

When the power button is pressed, the KB926QF (U18) pulls KBC_PWRBTN# low and must then release EC_ON to enable the secondary rails. For a "No Display" symptom where fans spin, check the +VCC_CORE rail at PL11/PL12. This rail is managed by PU10 (ISL6262). If VCC_CORE is missing, verify VR_ON from the EC. Additionally, the Intel Northbridge (GL40) on this model is prone to solder fatigue; verify the CLK_PCI_LPC (33MHz) using an oscilloscope. If the board cycles, a corrupted BIOS on U20 (SST25VF080B) is a frequent culprit—always backup and flash a "Clean ME" region dump specifically for the ICH9M chipset.

Download Schematic & Boardview Files

⏳ Please wait 120 seconds to unlock your Schematic & Boardview Files download...
🔎 Read the chip-level diagnostic notes above while you wait.

Professional Repair Assistance

Explore our technician resources:

No comments:

Post a Comment

Translate

AdBlock Detected!

Please support Genius Mind Technologies by disabling your AdBlocker. We rely on ads to keep our massive library of free schematics, boardviews, and BIOS bin files free for everyone.