Friday, November 20, 2026

Acer Aspire 5760 5760G (Compal LA-7071P) Schematic & Boardview Download + Chip-Level Diagnostic Guide

The Acer Aspire 5760 and 5760G series, built on the robust Compal LA-7071P (PI5W1) motherboard architecture, represents a classic era of Intel Sandy Bridge engineering. As a senior repair engineer, I often see these boards on the bench with common power-rail failures or PCH-related sequencing issues. This guide provides the technical breakdown necessary for chip-level troubleshooting, focusing on the specific Compal design language used in this platform.

Board Architecture & Technical Specifications

Feature Technical Specification
Motherboard Model / ODM Part Number Compal LA-7071P (PI5W1 / PI5W2)
Target Laptop Series / Form Factor Acer Aspire 5760, 5760G (15.6" Multimedia)
Chipset / CPU Architecture Intel HM65 / Sandy Bridge (2nd Gen Core i3/i5/i7)
Super I/O (EC/KBC) Controller ENE KB930QF A1
Key Voltage Rails & Switching Coils PL4 (+3VALW), PL5 (+5VALW), PL9 (+1.5VP), PL14/15 (+VCC_CORE)

Real-World Motherboard Diagnostic Procedures

1) DC-IN Protection & Charging Logic (ISL88731)

On the LA-7071P, the input power stage relies on the ISL88731C (PU1) charging IC to manage the entry MOSFETs PQ6 and PQ7. If the laptop is dead with no lights, first measure the voltage at the current sense resistor PR3. If you have 0V at PR3, check the gate voltage of PQ6/PQ7. The ISL88731 requires ACIN (Pin 2) to be approximately 3.2V (derived from a voltage divider on the adapter line) to release the gates. If ACIN is present but the gates aren't opening, check ACOK (Pin 13) which should be pulled high to 3.3V, signaling the EC (KB930QF) that the power source is valid.

2) Standby Rail Generation & Resistance Mapping

The +3VALW and +5VALW rails are generated by PU2 (RT8205L). This IC must first produce its internal LDO voltages: +3VLP (Pin 8) and +5VLP (Pin 17). These are critical for the EC's initial power-up. If the coils PL4 or PL5 are shorted to ground, do not immediately replace the PWM IC. On this Sandy Bridge platform, a low resistance on PL4 (+3VALW) often points to a shorted HM65 PCH or a leaky ceramic capacitor near the BIOS chip (U22). Normal resistance for +3VALW should be above 300Ω, while +5VALW should be in the kilo-ohm range.

3) Power-On Sequence & Signal State Tracking

Tracing the start-up sequence on this board requires monitoring the ENE KB930QF. When the power button is pressed, the signal ON/OFFBTN# drops to 0V at Pin 32. The EC should then release PCH_RSMRST# (Pin 100) to 3.3V. If RSMRST# stays low, the PCH will never exit the reset state. Furthermore, check the 32.768kHz RTC crystal (Y3) near the PCH; if this clock is absent or distorted, the PCH will not respond to the PM_PWRBTN# signal. If the board turns on but has no display, ensure +VGFX_CORE is generated at PL17 after the CPU core rails (PL14/15) have stabilized.

Download Schematic & Boardview Files

⏳ Please wait 120 seconds to unlock your Schematic & Boardview Files download...
🔎 Read the chip-level diagnostic notes above while you wait.

Professional Repair Assistance

Explore our technician resources:

No comments:

Post a Comment

Translate

AdBlock Detected!

Please support Genius Mind Technologies by disabling your AdBlocker. We rely on ads to keep our massive library of free schematics, boardviews, and BIOS bin files free for everyone.